8514-223-001 REV B page 1 COMMERCIAL WASHER MODEL T-300 VENDED C-SERIES CONTROL OPERATOR’S MANUAL INSTALLATION & OPERATION INSTRUCTIONS Please r
8514-223-001 REV B page 10 PROGRAMMING THE WASHER CONTROL The washer control can be programmed to prompt the user for alternate vend prices, change w
8514-223-001 REV B page 11 When manual programming mode is entered, the “Start”, “Hot”, “Warm” and “Cold” buttons perform alternate functions. Butto
8514-223-001 REV B page 12 Quick Test Option: When the Quick Test Option is chosen, the washer will begin a shortened wash cycle without the displayed
8514-223-001 REV B page 13 Prices Option: This option allows the user to set values for coin acceptor inputs and to set the vend price. It also allo
8514-223-001 REV B page 14 Cycles Option: This option allows the user to set the bath time and spin time for the “Wash” bath. It also allows the us
8514-223-001 REV B page 15 3. “Delay Spin” is meant to be used in applications where the amount of drain capacity is limited. In these cases the wash
8514-223-001 REV B page 16 Plus Cycle Options: The “Plus Cycle” options allow for the user to prompt the customer for varying vend prices based on add
8514-223-001 REV B page 17 “Final Rinse” bath. If the customer does not meet the vend price of the “Extra Rinse” feature, the prompt will time out and
8514-223-001 REV B page 18 Settings: The “Settings” options allow for the user to make various programming changes to change how the control operation
8514-223-001 REV B page 19 press the “Enter” button to move to the minutes. Once the hours and minute are both chosen, the “Enter” button must be held
8514-223-001 REV B page 2 TABLE OF CONTENTS Page No. Washer Specifications 2 Mounting Dimensions 3 Installation Instructions 4 Operating Instruc
8514-223-001 REV B page 20 Usage Menu: The Usage menu allows for the user to track data about machine usage. See below for detailed information on eac
8514-223-001 REV B page 21 The figure below shows the sub menu options for Usage:
8514-223-001 REV B page 22 Control Menu: The Control menu allows for the user to observe important technical information for the control. No changes c
8514-223-001 REV B page 23 COIN WASHER DEFAULT CYCLE The following table shows the complete details for the coin washer default cycle. Bath Bath Cyc
8514-223-001 REV B page 24 DISPLAYED WASHER FAULTS Displayed Fault Code Description DOOR LOCK ERROR Door Lock Error Condition This error is whe
8514-223-001 REV B page 25 Condition Invalid washer size jumper (harness) configuration. COMM ERROR2 Wrong Washer Size Jumper Configuration De
8514-223-001 REV B page 26 COMM ERROR5 VFD Communication Fault Condition This error is a data error on communications between the controller and the V
8514-223-001 REV B page 27 Condition This error is when the drive size does not match the washer size. DRIVE ERROR1 Washer size/ VFD size misma
8514-223-001 REV B page 28 DRIVE OV VFD Over-voltage Fault Condition This error is over-voltage on the VF drive Delay Delay time is 35 second
8514-223-001 REV B page 29 DRIVE GFI VFD Ground Fault Condition This error is a ground fault interruption on the VF drive Delay Delay time is
8514-223-001 REV B page 3
8514-223-001 REV B page 30 SERVICING AND TROUBLESHOOTING CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can c
8514-223-001 REV B page 31 Door will not open Thermoactuator Check to see if thermoactuator and its mechanism are stuck or binding and not allowing th
8514-223-001 REV B page 32 Water does not flush softener compartment. Water Valve Coil Check coil continuity at terminals and replace if no continuit
8514-223-001 REV B page 33 IMPORTANT TRANSIENT VOLTAGE SURGE SUPPRESSORS Like most electrical equipment your new machine can be damaged or have its
8514-223-001 REV B page 34 ACCESSORIES INSTALLATION: (Furnished) QTY. 9990-027-011 Hose, Water Supply 2 8641-242-000 Wash
8514-223-001 REV B page 4 INSTALLATION INSTRUCTIONS All washers must be installed in accordance with all local, state and national building, electric
8514-223-001 REV B page 5
8514-223-001 REV B page 6 PLUMBING Water supply hoses are furnished with each machine. The threaded connections on the hoses are ¾-11 ½ NHT. Separa
8514-223-001 REV B page 7 FUSING REQUIREMENTS: SINGLE-PHASE 115VAC MODELS - 20 AMP TIME-DELAY (DUAL ELEMENT) FUSE (or equivalent circuit breaker) SI
8514-223-001 REV B page 8 OPERATING INSTRUCTIONS - STARTING THE WASHER A. Load the clothes into the cylinder and latch the door securely. Be sure c
8514-223-001 REV B page 9 EMERGENCY STOP / SAFETY DOOR LOCK This machine is equipped with a Safety Door Lock that locks the door closed from when t
Kommentare zu diesen Handbüchern